Search Results

Prediction of power efficiency of gear boxes has become an increasingly important research topic since fuel economy requirements for passenger vehicles are more stringent, due to not only fuel cost but also environmental regulations. Under this circumstance, the automotive industry is dedicatedly focusing on developing a highly efficient gear box. Thus, the analysis of power efficiency of gear box should be performed to have a transmission that is highly efficient as much as possible at the beginning of design stage. In this study, a program is developed to analyze the efficiency of an entire gearbox, considering all components’ losses such as gear mesh, wet clutches, bearings, oil pump and so on. The analytical models are based on the formulations of each component power loss model which has been developed and published in many existing papers. The program includes power flow analysis of both a parallel gear-train and a planetary gear-train.

It has been discussed in numerous prior studies that in-neutral coasting, or sailing, can accomplish considerable amount of fuel saving when properly used. The driving maneuver basically makes the vehicle sail in neutral gear when propulsion is unnecessary. By disengaging a clutch or shifting the gear to neutral, the vehicle may better utilize its kinetic energy by avoiding dragging from the engine side. This strategy has been carried over to series production recently in some of the vehicles on the market and has become one of the eco-mode features available in current vehicles. However, the duration of coasting must be long enough to attain more fuel economy benefit than Deceleration Fuel Cut-Off (DFCO) - which exists in all current vehicle powertrain controllers - can bring. Also, the transients during shifting back to drive gear can result in a drivability concern.

This paper presents the development of a CarSim model of an All-Terrain Vehicle (ATV) that can be used to predict the handling and stability characteristic of the vehicle. The inertia and suspension characteristics of a subject ATV are measured and a model of the ATV is built in CarSim based on the measurements. A simplified suspension model is developed to convert the suspension compliance measurements into parameters suitable to a CarSim model. Procedures used to apply vehicle mass, inertia and suspension kinematics data in CarSim are also shown. The model is evaluated using predictions of vehicle response during a constant radius circle test. The simulation results of the maneuver are compared with the field test results shown in a recent CPSC report on ATV’s. Similar cornering characteristics are found in both results. Modifications are made to the model to study how changes to the ATV affect performance.

Springback affects the dimensional accuracy and final shape of stamped parts. Accurate prediction of springback is necessary to design dies that produce the desired part geometry and tolerances. Springback occurs after stamping and ejection of the part because the state of the stresses and strains in the deformed material has changed. To accurately predict springback through finite element analysis, the material model should be well defined for accurate simulation and prediction of stresses and strains after unloading. Despite the development of several advanced material models that comprehensively describe the Bauschinger effect, transient behavior, permanent softening of the blank material, and unloading elastic modulus degradation, the prediction of springback is still not satisfactory for production parts. Dies are often recut several times, after the first tryouts, to compensate for springback and achieve the required part geometry.

In order to improve the vehicle’s fuel economy while in cruise, the Model Predictive Control (MPC) technology has been adopted utilizing the road grade preview information and allowance of the vehicle speed variation. In this paper, a focus is on robustness study of delivered fuel economy benefit of Adaptive Nonlinear Model Predictive Controller (ANLMPC) reported earlier in the literature to several noise factors, e.g. vehicle weight, fuel type etc. Further, the vehicle position is obtained via GPS with finite precision and source of road grade preview might be inaccurate. The effect of inaccurate information of the road grade preview on the fuel economy benefits is studied and a remedy to it is established.

Commercial vehicles require continual improvements in order to meet fuel emission standards, improve diesel aftertreatment system performance and optimize vehicle fuel economy. Aftertreatment systems, used to remove engine NOx, are temperature dependent. Variable valve actuation in the form of cylinder deactivation (CDA) has been shown to manage exhaust temperatures to the aftertreatment system during low load operation (i.e., under 3-4 bar BMEP). During cylinder deactivation mode, a diesel engine can have higher vibration levels when compared to normal six cylinder operation. The viability of CDA needs to be implemented in a way to manage noise, vibration and harshness (NVH) within acceptable ranges for today’s commercial vehicles and drivelines. A heavy duty diesel engine (inline 6 cylinder) was instrumented to collect vibration data in a dynamometer test cell.

Autonomous vehicle technology has been developing rapidly in recent years. Vehicle parametric uncertainty in the vehicle model, variable time delays in the CAN bus based sensor and actuator command interfaces, changes in vehicle sped, sensitivity to external disturbances like side wind and changes in road friction coefficient are factors that affect autonomous driving systems like they have affected ADAS and active safety systems in the past. This paper presents a robust control architecture for automated driving systems for handling the abovementioned problems. A path tracking control system is chosen as the proof-of-concept demonstration application in this paper. A disturbance observer (DOB) is embedded within the steering to path error automated driving loop to handle uncertain parameters such as vehicle mass, vehicle velocities and road friction coefficient and to reject yaw moment disturbances.

Future SAE Level 4 and Level 5 autonomous vehicles will require novel applications of localization, perception, control and artificial intelligence technology in order to offer innovative and disruptive solutions to current mobility problems. This paper concentrates on low speed autonomous shuttles that are transitioning from being tested in limited traffic, dedicated routes to being deployed as SAE Level 4 automated driving vehicles in urban environments like college campuses and outdoor shopping centers within smart cities. The Ohio State University has designated a small segment in an underserved area of campus as an initial autonomous vehicle (AV) pilot test route for the deployment of low speed autonomous shuttles. This paper presents initial results of ongoing work on developing solutions to the localization and perception challenges of this planned pilot deployment.

Compared to the internal-combustion-engine (ICE) vehicles on the road today, Electric Vehicles (EV) deliver more torque to vehicle wheels, and require smaller driveline packaging envelopes. Current differentials use asymmetrical ring gears with differential housings that are roughly a third of the tire outside diameter. New differential architecture concepts are shown here to deliver more torque to the wheels, while decreasing the height of the differential as much as fourfold. Most EV’s are driven by one or more torsion motors, delivering torque to the left side and the right side of the EV’s at different speeds during a vehicle turn, or a wheel “spinout.” At low speeds, the EV motors deliver more torque to the wheels than comparably sized ICE vehicles, so EV differentials must be built stronger and stiffer to manage the distribution of available drive torque.

This paper describes a systematic approach to identify the best sensor combination by performing sensor placement analysis to detect and isolate clutch stuck-off faults in Automatic Transmissions (AT) based on structural analysis. When an engaged clutch in the AT loses pressure during operation, it is classified as a clutch stuck-off fault. AT can enter in neutral state because of these faults; causing loss of power at wheels. Identifying the sensors to detect and isolate these faults is important in the early stage of the AT development. A universal approach to develop a structural model of an AT is presented based on the kinematic relationships of the planetary gear set elements. Sensor placement analysis is then performed to determine the sensor locations to detect and isolate the clutch stuck-off faults using speed sensors and clutch pressure sensors. The proposed approach is then applied to a 10-Speed AT to demonstrate its effectiveness.

Electric vehicles (EVs) and hybrid electric vehicles (HEVs) are getting more attention in the automotive industry with the technology improvement and increasing focus on fuel economy. For EVs and HEVs, especially all-wheel drive (AWD) EVs with two electric motors powering front and rear axles separately, an accurate motor speed measurement through resolver is significant for vehicle performance and drivability requirement, subject to resolver faults including amplitude imbalance, quadrature imperfection and reference phase shift. This paper proposes a diagnostic scheme for the specific type of resolver fault, amplitude imbalance, in AWD EVs. Based on structural analysis, the vehicle structure is analyzed considering the vehicle architecture and the sensor setup. Different vehicle drive scenarios are studied for designing diagnostic decision logic. The residuals are designed in accordance with the results of structural analysis and the diagnostic decision logic.

The nonlinear behavior of automotive powertrains is mainly due to the presence of backlash between engaging components. In particular, during tip-in or tip-out maneuvers, backlash allows the generation of impacts that negatively affect the vehicle NVH performance. Due to the faster response of electric motors with respect to conventional internal combustion engines, this problem is even more critical for electric vehicles. In order to employ numerical optimal control methods for backlash compensation, the system states have to be known. In this paper, an electric powertrain is modeled as a two-mass oscillator with lumped backlash. This model estimates the system states when in no-contact mode while a Kalman filter that relies only on commonly available speed measurements is active in the contact phase. The powertrain model is validated using experimental data collected during vehicle testing and the online estimated half-shaft torque is shown.

An important part of automotive driving assistance systems and autonomous vehicles is speed optimization and traffic flow adaptation. Vehicle sensors and wireless communication with surrounding vehicles and road infrastructure allow for predictive control strategies taking near-future road and traffic information into consideration to improve fuel economy. For the development of autonomous vehicle speed control algorithms, it is imperative that the controller can be evaluated under different realistic driving and traffic conditions. Evaluation in real-life traffic situations is difficult and experimental methods are necessary where similar driving conditions can be reproduced to compare different control strategies. A traditional approach for evaluating vehicle performance, for example fuel consumption, is to use predefined driving cycles including a speed profile the vehicle should follow.

Increased demands for reduction of fuel consumption and CO2 emissions are driven by the global warming. To meet these challenges with respect to the passenger car segment the strategy of utilizing IC-engine downsizing has shown to be effective. In order to additionally meet requirements for high power and torque output supercharging is required. This can be realized using e.g. turbo-chargers, roots blowers or a combination of several such devices for the highest specific power segment. Both turbo-chargers and roots blowers can be strong sources of sound depending on the operating conditions and extensive NVH abatements such as resonators and encapsulation might be required to achieve superior vehicle NVH. For an efficient resonator tuning process in-duct acoustic source data is required. No published studies exists that describe how the gas exchange process for roots blowers can be described by acoustic sources in the frequency domain.

As the development of autonomous vehicles rapidly advances, the use of convoying/platooning becomes a more widely explored technology option for saving fuel and increasing the efficiency of traffic. In cooperative adaptive cruise control (CACC), the vehicles in a convoy follow each other under adaptive cruise control (ACC) that is augmented by the sharing of preceding vehicle acceleration through the vehicle to vehicle communication in a feedforward control path. In general, the desired velocity optimization for vehicles in the convoy is based on fuel economy optimization, rather than driveability. This paper is a preliminary study on the impact of the desired velocity profile on the driveability characteristics of a convoy of vehicles and the controller gain impact on the driveability. A simple low-level longitudinal model of the vehicle has been used along with a PD type cruise controller and a generic spacing policy for ACC/CACC.

The Ohio State University EcoCAR 3 team is building a plug-in hybrid electric vehicle (PHEV) post-transmission parallel 2016 Chevrolet Camaro. With the end-goal of improving fuel economy and reducing tail pipe emissions, the Ohio State Camaro has been fitted with a 32 kW alternator-starter belt coupled to a 119 kW 2.0L GDI I4 engine that runs on 85% ethanol (E85). The belted alternator starter (BAS) which aids engine start-stop operation, series mode and torque assist, is powered by an 18.9 kWh Lithium Iron Phosphate energy storage system, and controlled by a DC-AC inverter/controller. This report details the modeling, calibration, testing and validation work done by the Ohio State team to fast track development of the BAS system in Year 2 of the competition.

Functionally graded materials enable structures to have distribution of different properties (physical, thermal, electrical, mechanical, etc.) across its volume; achievable via material/ design/ process engineering. These functionally graded materials can find an application in systems which demand localized variation or enhancement in properties in different regions of the same component. In this paper, we focus on the potential ways of designing functionally graded polymer composite structure by injection molding process. Advanced mold designs for injection molding process can be effectively used to manufacture the functionally graded structures. Innovative design approach has been explored to control the distribution of the filler content /orientation to impart distinctive properties across the cross section / geometry without affecting the bulk properties.

Light weight structures give significant advantages to products in the Industrial sector. Component weight-saving plays a major role in improving the efficiency and performance of assembled systems. The introduction of lighter materials into products using dissimilar material joining techniques can create more weight savings and leads to lighter structures. Structural optimization is another method to optimize the material layout without affecting overall performance of the product. This paper discusses the methods to create lighter structures by the introduction of lighter materials in structures and structural optimization methods. Lighter materials are introduced in the structure using dissimilar material joining techniques. Joining processes such as thermal shrink-fit and mechanical press-fit are useful for metal to metal components. Similarly, adhesively bonded joints are useful for both metal and non-metal (plastics and composites) components.

Fuel economy is one of the major challenges for both on and off-road vehicles. Inefficient engine operation and loss of kinetic energy in the form of heat during braking are two of the major sources of wasted fuel energy. Rising energy costs, stringent emission norms and increased environmental awareness demand efficient drivetrain designs for the next generation of vehicles. This paper analyzes three different types of powertrain concepts for efficient operation of a forklift truck. Starting from a conventional torque convertor transmission, hydrostatic transmission and a hydraulic hybrid transmission (Eaton architecture) are compared for their fuel economy performance. Eaton hydraulic hybrid system is seen to perform much better compared to other two architectures. Improved fuel economy is attributed to efficient engine operation and regeneration of vehicle kinetic energy during braking.

This study was performed to showcase the possible applications of the Hardware-in-the-loop (HIL) simulation environment developed by the National Highway Traffic Safety Administration (NHTSA), to test heavy truck crash avoidance safety systems. In this study, the HIL simulation environment was used to recreate a simulation of an actual accident scenario involving a single tractor semi-trailer combination. The scenario was then simulated with and without an antilock brake system (ABS) and electronic stability control (ESC) system to investigate the crash avoidance potential afforded by the tractor equipped with the safety systems. The crash scenario was interpreted as a path-following problem, and three possible driver intended paths were developed from the accident scene data.